What Happens If You Overfill Power Steering Fluid?

Have you ever wondered what would happen if you overfilled your car’s power steering fluid? Are you worried that too much fluid might cause damage to your vehicle’s power steering system? 

Power steering reservoir overflowing can have serious consequences, including decreased performance and potential damage to the power steering pump and other components. This article will explore the effects of an overfilled power steering system and how to avoid it.

What Happens If You Overfill Power Steering Fluid

What Is The Purpose Of Powering Steering Fluid? 

Power steering fluid also plays a similar role to engine or transmission grease. This type of solution helps the vehicle’s power steering to operate more smoothly and stably. 2AZ-FE transmission oil is one of the top priorities for Toyota’s famous Camry, have you tried it?

Besides, assisting in maintaining the durability and limiting the damage caused by friction are other excellent capabilities of Power Steering Fluid.

Unlike the cars of the past, modern cars have more support mechanisms and relatively heavy frames to ensure the driver’s safety. But because of that, the support mechanisms are under more pressure from the system. Therefore, it is easy to understand when a continuous collision occurs when we operate the car for a long time, causing many serious consequences.

But fortunately, we can keep the parts safe if there is a constant flow of lubricating fluid to limit wear. Therefore, the power steering always needs the necessary amount of oil to operate smoothly.

Do you need to fill the power steering fluid? 

Although there is no direct impact, pouring too much power steering oil will have serious consequences.

Although the lack of power steering oil will cause a lot of trouble when operating the car. But that does not mean that we can agree with the statement that “more is better than less” and try to give as much liquid as possible.

Theoretically, you shouldn’t find a link between heavy use of power steering fluid and vehicle damage. Because the system will work in one place while the power steering oil tank is again in another area.

However, once the capacity of the storage area is exceeded, the excess liquid will begin to leak out. There are many causes for this phenomenon, the most typical of which is temperature change. But no matter where it originates, the power steering oil will begin to negatively affect the parts with which this filling power steering fluid comes in contact.

What Happens If You Overfilled Power Steering Fluid? 

Power Steering Fluid does overfill the power steering reservoir always causes dozens of adverse effects to the system inside the car. The engine and many other parts face problems caused by this fluid. 

And here are the 3 most common phenomena you may encounter if the flow is too much power steering fluid.

Fluid leakage and make a mess for your engine

Fluid leakage and make a mess for your engine

Power steering oil is also a typical liquid, so it is not difficult to understand when this chemical will expand and increase in volume when exposed to high temperatures. And this is also the leading cause of leakage of this solution out of the tank.

At this point, the oil will begin to spread and reach different areas in the engine system. In some parts with hot surfaces, the liquid will quickly evaporate and form deposits that cause corrosion or reduce heat dissipation.

In addition, some belts will also lose stability when the surface becomes more slippery. And the consequence of this phenomenon is that the wire will ultimately break and stop all vehicle activities.

Engine parts are prone to wear

The problem can be even more severe if liquid leaks into the nuts or gaskets, especially the rubber gasket. Chemical reactions will take place, and the corrosion process will quickly begin. After only a short time, you can see the terrible destruction of this residual oil.

Even the long-lasting stains created by this solution will slowly erode the metal surface if you do not take care of it quickly. Ultimately, the vehicle’s performance will be severely degraded or wholly damaged because of a small amount of liquid leakage.

Start A Fire

Start A Fire

Although the rate of power steering oil catching fire and burning is not high, it does not mean we can underestimate this risk. There have been several cases of fires for this reason. So it would help if you also took precautions to ensure safety.

The relatively sturdy construction of the power steering lubricant gives this mixture a relatively high flash point of up to 400 degrees F. In contrast, most flammable compounds will only have a flash point of 100. But that doesn’t mean we can be complacent.

Cause smoke

All liquids will begin to expand when exposed to high temperatures, and this process will gradually end if the solution is completely evaporated. 

And that is also the primary mechanism to explain why a power steering fluid leak will produce an abnormal amount of smoke when the vehicle operates.

This chemical will evaporate quickly if spilled into high-temperature parts, especially the engine or exhaust. Eventually, the whole thing will vaporize and escape. But during this process, the non-volatile substances will tend to deposit, interfering with the operation.

In the worst case, smoke can be a precursor to a fire. So even a few drops of oil can cause a catastrophic failure.

How To Drain Excess Power Steering Fluid

How To Drain Excess Power Steering Fluid? 

Don’t worry about accidentally giving too much power steering fluid into the container. We can handle this excess solution in many ways before it must be taken to professional centers.

Using a turkey baster or syringe and flushing the power steering fluid is the fastest and safest among the most common methods. You can refer to the steps below.

Using a turkey baster or syringe

With just a syringe or turkey baster, you can handle some excess liquid inside the container. However, this method cannot access the oil in the system. It would help if you considered further intervention in various ways.

The syringes advantage is that you can reuse the excess oil after sucking it out. We will comfortably store liquids if the proper containers are prepared for other necessary cases.

In addition, you need to follow the procedure below to ensure that the right amount of oil is extracted without affecting other factors.

  • Step 1: Vacuum the amount of oil that you think is suitable
  • Step 2: Add a small amount of new oil to the existing reservoir of old power steering oil
  • Step 3: Start the car and move continuously for about 20 minutes. You can start the engine with or without load as you like. Because the purpose of this step is to mix the new and old oil
  • Step 4: Use a turkey baster to suck out all the oil and add an unknown liquid.

Flushing the power steering fluid

Draining the power steering fluid is the perfect solution if you want to get to the bottom of any remaining liquid in your system. However, it will take some effort and time to implement this method.

  • Step 1: Since we will need to operate under the car, the first operation is always to push the car up with a hydraulic jack to access the area below.
  • Step 2: You will need to find the plug of the oil pipe, return the line, and put the replacement plastic pipe in
  • Step 3: Raise the top of the plastic pipe and then put the return tube to prevent the conduction fluid from going back into the system
  • Step 4: Drive the car to help the oil flow down faster. It is best to warm up so that the heat helps speed up this process
  • Step 5: Remember to turn off the car engine before proceeding with other tasks
  • Step 6: Reinstall the guide nut and tighten the screw
  • Step 7: Start the car again and steer to remove air bubbles

When Should You Change The Power Steering Fluid

When Should You Change The Power Steering Fluid? 

According to the advice of most car manufacturers, the appropriate time to change the power steering oil is every 60,000 – 80,000 km. However, this milestone should not be a fixed number.

We can encounter a lot of problems while traveling in a vehicle. It causes many errors that can seriously affect the amount of transmission fluid. That is why you must regularly monitor with both feeling and accurate information.

In addition, always be ready to take the vehicle to replace the fluid whenever strange phenomena occur.


How full should the power steering fluid be?

The answer will depend on the size of the fluid chamber inside your vehicle. Each of these components has MIN and MAX markings to divide the amount of liquid to be added. Based on these factors, please decide what amount of filling power steering fluid is necessary.

How do you bleed air out of the power steering?

You will need to open the bleed valve first. Remember to operate it carefully to avoid damaging this part. Then try to steer by turning the steering wheel as much as possible. This action will help the oil move, limiting air bubbles’ appearance.

Does the air in the power steering damage the pump?

Air bubbles, when compressed due to the action of the flow, will create enormous pressure on the mechanisms, especially the hinge system. The result is that these sensitive parts will soon no longer function properly.

Is it OK to add more power steering fluid?

The answer would be no because the car cannot increase performance even if you try to add more fluid. Any attempt will only bring about severe consequences for the system.

What happens if the power steering pump runs dry?

There will be problems if you move while running out of power steering fluid. At this time, the parts above will continuously rub directly against each other without any protection. It leads to heat problems, damage, and, worse, complete cracking.


So I helped you identify what happens if you overfill power steering fluid. After today’s article, I hope you know how significant the consequences of such action are. From there, the most effective prevention and treatment measures can be obtained.

Leave a Comment